1/22/2024 0 Comments Diy pencil cupThis was one skill my Dad taught me as a kid, and it has come in handy here. I cut a piece of ribbon about 20″ long and tied it along the top of my can like you would a real tie. I folded down my white felt at the top to create the collar of my shirt, and then applied buttons down the front with little dots of glue. I used my can as a template, and cut out the circle bottom piece with a scissors. To clean up the bottom edges, I glued another piece of felt on the bottom. I would fold in a section, glue, then repeat until the whole bottom was secure. Then, I hot glued the remaining fabric on the bottom of my can, gluing one section at a time. I finished off by securing one edge of my blue fabric under the other, creating the “front” of the shirt. I started right at the seam of my white felt piece and glued my blue pinstripe fabric all around the can. I created a “hem” along the top and glued it just up to the edge of my can, right on top of the felt. I used my glue gun to attach about a 1″ portion of the felt along the top. I used a piece of white felt about 9 1/2 ” x 2 1/2″, just long enough to wrap around the circumference of the top of my can. You will need about 10″ x 6″ square of fabric to work with, just big enough to wrap around your recycled can.Īnd no dress shirt would be complete without a collar, right? I wanted to use one that had the pattern and look of a man’s shirt. Truth be told, the blue pinstripe fabric actually from one of my husband’s shirts that he donated to my craft pile after there was a stain on the front that wouldn’t come out, but you can use any fabric swatch. I started with a recycled soup can, some white felt, blue pinstripe fabric, 1/2″ thick coordinating ribbon, buttons, and my handy dandy glue gun. Learn to make fun upcycling crafts and furniture, make your own cleaning products, grow your own food and make ALL your own beauty products from face creams to mascara.Father’s Day is just around the corner, and if you are looking for a fun and easy craft for the kids to create, you will love this upcycled can turned into a cool suit and tie pencil holder. This book contains over 80 DIYs, recipes and tips on how to live greener and leaner. Screw a bulb into the chandelier light fixture, plug in your light a voila! Great idea!įor the best circular saw reviews, click here. Put the plastic cover back on the plug and tighten the screws. Wrap one wire (either one) around each screw and then tighten. Use the screwdriver to loosen the screws on the plug and open it up. Strip 1/2 inch of rubber shielding off the two loose ends of the wire. Tighten until the whole lamp fitting is secured. Pass the nut over the other end of the wire and screw it down onto the exposed threaded pipe at the bottom of the saucer. This is the kind of chandelier fitting i use: This is the kind of steel threaded lamp nipple I use: Try to find a light socket that will accept the same thread size and pitch as the threaded lamp nipple, and screw the lamp socket on to one end, the end inside the tea cup. Wind one wire around each screw and tighten. Use the screw driver to loosen the screws on both sides of the chandelier fitting. Split the wire and strip 1/2 inch of plastic coating off the ends of the wire that are on the inside of the cup. Use the wire cutters to cut a length of wire and feed it through the steel threaded lamp nipple. Put the cup and saucer together and slide the steel threaded lamp nipple through them. This is the kind of 1/2-inch diamond hole saw drill bit I use: Drill slowly and don’t apply too much pressure until you have a hole in the bottom of your cup. Pour a little water over the bottom of the cup and place the drill bit on your pencil mark at a 45 degree angle. Slowly start to drill into the bottom. Put on the gloves and welding safety glasses before using the drill. Turn your cup and saucer over and mark the center with a pencil.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |